Question 1

It is normal for more than one decoder output to be active at the same time.

Accepted Answer

A) True 
 B)False

Question 2

A digital_____or data selector is a logic circuit that accepts several digital data inputs and selects one of them at any given time to pass on to the output.

Accepted Answer

The answer of A digital_____or data selector is a logic...

Question 3

Approximately how much current would be required to operate the number 6 on a 7- segment LED display if each segment requires 10 mA?

Accepted Answer

A)   70 mA
B)   60 mA
C)   40 mA
D)   50 mA

Question 4

Basically, a multiplexer changes parallel data inputs to a serial output.

Accepted Answer

A) True 
 B)False

Question 5

A(n) _____	has a number of input lines, only one of which is activated at a given time, and produces an N- bit output code, depending on which input is activated.

Accepted Answer

The answer of A(n) _____	has a number of input lines,...

Question 6

A demultiplexer accepts data from:

Accepted Answer

A)   multiple input lines and transfers it to one output line.
B)   sequential input lines and transfers it to one output line.
C)   one input line and transfers it to one output line after conditioning and buffering the data signals.
D)   one input line and transfers it to multiple output lines. D

Question 7

Magnitude comparators are useful for speed control, temperature control, and level control. After these analog quantities are sampled:

Accepted Answer

A)   quantities are permanently stored in memory location.
B)   quantities are converted to binary equivalent.
C)   quantities are converted to a constant current source.
D)   quantities are converted to equivalent frequency through another converter.

Question 8

A(n)	_____display controls the reflection of available light.

Accepted Answer

The answer of A(n)	_____display controls the reflection of available light....

Question 9

The relatively slow transition time of data on bus lines may be attributed directly to capacitive loading of the lines.

Accepted Answer

A) True 
 B)False

Question 10

Common anode seven segment displays could be considered active high loads.

Accepted Answer

A) True 
 B)False

Question 11

LCD displays are more visible in low light conditions than LED displays.

Accepted Answer

A) True 
 B)False

Question 12

The IEEE/ANSI symbol for a decoder has the internal designation BCD/DEC, how many pins; including Vcc and ground, would this IC have?

Accepted Answer

A)   18
B)   14
C)   16
D)   20

Question 13

A numeric display - driven by a 744X driver - is used to display the output from a BCD counter. If this counter only displays the numbers 0, 2, 4, 6, and 8, then troubleshooting should be narrowed down to:

Accepted Answer

A)   the "b", "c", and "d" segments on the numeric display.
B)   the MSB line on the display input circuit.
C)   the MSB line on the driver input circuit.
D)   the LSB line on the display input circuit.
E)   the LSB line on the driver input circuit.

Question 14

A three- line- to- eight line decoder has inputs CBA where A is the LSB. The output AND gates are labeled Q0 through Q7. The output of AND gate Q4 should be active when the inputs are:

Accepted Answer

A)   0 through Q7. The output of AND gate Q4 should be active when the inputs are: 
A)     
B)     
C)     
D)   " class="answers-bank-image d-inline" rel="preload" >
B)   0 through Q7. The output of AND gate Q4 should be active when the inputs are: 
A)     
B)     
C)     
D)   " class="answers-bank-image d-inline" rel="preload" >
C)   0 through Q7. The output of AND gate Q4 should be active when the inputs are: 
A)     
B)     
C)     
D)   " class="answers-bank-image d-inline" rel="preload" >
D)  0 through Q7. The output of AND gate Q4 should be active when the inputs are: 
A)     
B)     
C)     
D)   " class="answers-bank-image d-inline" rel="preload" > B

Question 15

The select inputs to a multiplexer may also be called address lines.

Accepted Answer

A) True 
 B)False

Question 16

A multiplexer/data selector is a logic circuit that:

Accepted Answer

A)   accepts data inputs from multiple lines and passes this data to multiple output lines.
B)   accepts data inputs from several lines and multiplexes this input data to four BCD lines.
C)   accepts data inputs from one line and passes this data to multiple output lines.
D)   accepts data inputs from several lines and allows one of them at a time to pass to the output.

Question 17

A demultiplexer does not use an OR gate as the output gate because of the multiple output lines.

Accepted Answer

A) True 
 B)False

Question 18

In the event that a 9 and a 1 were entered simultaneously, a _____encoder would encode only the 9.

Accepted Answer

priority

Question 19

Number system conversion can be accomplished using encoders.

Accepted Answer

A) True 
 B)False

Question 20

More than one active input to an encoder will often produce an erroneous output. This problem may be partially overcome by the use of:

Accepted Answer

A)   an open- collector NAND gate whose inputs are connected to the decoder's outputs.
B)   an additional encoder whose inputs are cascaded to the original decoder's outputs.
C)   a priority encoder to ensure that when more than one input is active the output will correspond to the lowest- numbered input.
D)   a priority encoder to ensure that when more than one input is active the output will correspond to the highest- numbered input.

Exam 9: MSI Logic Circuits

It is normal for more than one decoder output to be active at the same time.

Correct AnswerverifiedShow Answer

A digital_____or data selector is a logic circuit that accepts several digital data inputs and selects one of them at any given time to pass on to the output.

Correct AnswerverifiedShow Answer

Approximately how much current would be required to operate the number 6 on a 7- segment LED display if each segment requires 10 mA?

Correct AnswerverifiedShow Answer

Basically, a multiplexer changes parallel data inputs to a serial output.

Correct AnswerverifiedShow Answer

A(n) _____ has a number of input lines, only one of which is activated at a given time, and produces an N- bit output code, depending on which input is activated.

Correct AnswerverifiedShow Answer

A demultiplexer accepts data from:

Correct AnswerverifiedD

Magnitude comparators are useful for speed control, temperature control, and level control. After these analog quantities are sampled:

Correct AnswerverifiedShow Answer

A(n) _____display controls the reflection of available light.

Correct AnswerverifiedShow Answer

The relatively slow transition time of data on bus lines may be attributed directly to capacitive loading of the lines.

Correct AnswerverifiedShow Answer

Common anode seven segment displays could be considered active high loads.

Correct AnswerverifiedShow Answer

LCD displays are more visible in low light conditions than LED displays.

Correct AnswerverifiedShow Answer

The IEEE/ANSI symbol for a decoder has the internal designation BCD/DEC, how many pins; including Vcc and ground, would this IC have?

Correct AnswerverifiedShow Answer

A numeric display - driven by a 744X driver - is used to display the output from a BCD counter. If this counter only displays the numbers 0, 2, 4, 6, and 8, then troubleshooting should be narrowed down to:

Correct AnswerverifiedShow Answer

A three- line- to- eight line decoder has inputs CBA where A is the LSB. The output AND gates are labeled Q0 through Q7. The output of AND gate Q4 should be active when the inputs are:

Correct AnswerverifiedB

The select inputs to a multiplexer may also be called address lines.

Correct AnswerverifiedShow Answer

A multiplexer/data selector is a logic circuit that:

Correct AnswerverifiedShow Answer

A demultiplexer does not use an OR gate as the output gate because of the multiple output lines.

Correct AnswerverifiedShow Answer

In the event that a 9 and a 1 were entered simultaneously, a _____encoder would encode only the 9.

Correct Answerverifiedpriority

Number system conversion can be accomplished using encoders.

Correct AnswerverifiedShow Answer

More than one active input to an encoder will often produce an erroneous output. This problem may be partially overcome by the use of:

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
D

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

The IEEE/ANSI symbol for a decoder has the internal designation BCD/DEC, how many pins; including V_ccand ground, would this IC have?

Correct Answer
verified

Correct Answer
verified

A three- line- to- eight line decoder has inputs CBA where A is the LSB. The output AND gates are labeled Q₀through Q₇. The output of AND gate Q₄should be active when the inputs are:

Correct Answer
verified
B

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
priority

Correct Answer
verified

Correct Answer
verified